NOVAFORGE LABS
← Back to store
Research use only. For laboratory research use only — not for human or animal consumption. Not a drug, supplement, food, cosmetic, or medical device. Not evaluated or approved by the FDA for any use.

Research guides · Updated November 2026

Third-Party Tested Research Peptides

Every NovaForge Labs lot is tested by an independent US laboratory before release, and each lot has its own certificate of analysis that you can look up with the lot number from your order confirmation.

What third-party testing actually means

A certificate of analysis is only as useful as the lab behind it. When a supplier tests its own material in house, the same party that profits from a passing number also produces it. Third-party testing removes that conflict: an outside laboratory with no stake in the sale receives a sample, runs the analysis, and issues the report under its own name.

For research peptides, a meaningful third-party COA answers three separate questions. Is this the compound on the label? How much of the material is that compound, as opposed to related impurities? And how much peptide is actually in the vial? Those are identity, purity, and content, and they are measured by different methods.

A COA that reports only a purity percentage, with no identity method and no lab name, leaves the most important question open. A 99% pure sample of the wrong sequence is still the wrong sequence. That is why we publish which lab tested each lot and which methods it used.

What we test on every lot

No NovaForge lot is released for sale until an independent US lab has tested it. Lots that come back below 99% HPLC purity are not released. We work with two laboratories, and each COA states which one performed the work.

LaboratoryIdentity methodPurity methodContent
ILS LaboratoriesHPLC retention time matched against a reference standardHPLC (UV detection)Not reported
Freedom DiagnosticsLC-MS (observed mass vs. theoretical mass)HPLC (UV detection)Net content in mg

HPLC purity is the share of the UV signal that falls under the main peak of the chromatogram. It tells you how clean the material is relative to closely related impurities such as truncated or modified sequences.

Identity confirms the compound itself. A retention-time match shows the sample behaves like a known reference standard on the same column. LC-MS goes a step further and measures molecular mass directly, so the observed value can be compared to the theoretical mass of the sequence.

Net content is a separate measurement of how many milligrams of peptide are present. Purity and content are not the same number, and a vial can be very pure while holding less material than stated. Our guide to HPLC purity vs. net peptide content explains the difference in detail.

How to look up the COA for your lot

Every COA we publish is tied to one specific lot. To find the report that matches the material you received:

  1. Open your order-confirmation email. Your lot number is listed there. It is not printed on the vial.
  2. Go to lot verification and enter the lot number.
  3. The page returns the matching COA, including the testing lab, methods, and measured values.

Lot numbers follow a format like NFL-0001 or NFL-0002. Each compound's batches are numbered on their own sequence, so the same lot number can appear on two different products. Each lot and compound pair maps to its own COA number, such as Nova2608180234. Our guide to peptide lot numbers covers this in more depth.

If you would rather browse, the full COA registry lists every published report by compound and lot.

Independent listings and outside verification

Our own COAs are one layer. Several independent platforms have also looked at NovaForge material or records:

Each of these platforms uses its own method and scope, and none of them replaces checking the COA for your specific lot. Taken together, they give you more than one way to confirm that what we publish matches what the labs reported. For a broader checklist, see how to verify a peptide vendor.

The numbers across our published COAs

We publish our COA data as an open dataset so anyone can check the spread rather than rely on a single headline figure. The lab dataset currently covers 26 COAs.

MeasureValue
COAs in the dataset26
Median HPLC purity99.78%
Range99.03% to 99.99%
Lots at or above 99.5%20 of 26
Format and licenseCSV, CC BY 4.0

The dataset is licensed CC BY 4.0, which means researchers, reviewers, and other sites can reuse it with attribution. Publishing the full range, including the lowest lots, is deliberate. A range tells you more about a supplier's consistency than a single best-case number.

What a COA does and does not tell you

A COA describes the sample the lab tested at the time it was tested. It confirms identity, purity, and, where reported, content for that lot. It does not describe how material was stored after it left our facility, and it does not cover tests that were not run.

A standard peptide COA, for example, does not usually include endotoxin or sterility testing unless the report says so. Read what a report actually contains rather than assuming. Our guide on how to read a peptide COA walks through each field, and peptide testing labs explained compares common lab methods.

Storage also matters once material arrives. Lyophilized peptides hold up best sealed, dry, dark, and cold. See how to store lyophilized peptides for lab handling practices.

Browse the catalog by research area

All NovaForge products are sold strictly for research use only and are not for human or animal use. Most ship lyophilized (freeze-dried). The Semax and Selank nasal spray presentations and bacteriostatic water ship as liquids.

You can browse the full catalog at the shop, or start from a research-area hub:

Every product page links to the COA registry, and every order confirmation includes the lot number you need to pull the report for your vial.

Frequently asked questions

What does third-party tested mean for research peptides?

It means an independent laboratory with no financial stake in the sale tested a sample of the lot and issued the report under its own name. For NovaForge, every lot is tested by an independent US lab before release, and each certificate of analysis names the lab and the methods it used for identity and purity.

Is every NovaForge lot tested, or just some?

Every lot is tested before it is released for sale. Lots that measure below 99% HPLC purity are not released. Each COA is specific to one lot of one compound, so the report you look up describes the batch you received rather than a representative sample from an earlier run.

Where do I find my lot number?

Your lot number is in your order-confirmation email. It is not printed on the vial. Enter it on the lot verification page and the matching certificate of analysis will appear, including the testing lab, the identity method, and the measured HPLC purity for that specific lot and compound.

Does HPLC purity tell me how much peptide is in the vial?

No. HPLC purity is the share of the UV signal under the main peak, which describes how clean the material is relative to related impurities. Net content, reported in milligrams, is a separate measurement. Freedom Diagnostics COAs report net content; ILS Laboratories COAs report identity and purity.

Can I reuse the NovaForge COA dataset?

Yes. The dataset of 26 COAs is published as a CSV under a CC BY 4.0 license, which allows reuse with attribution. It includes the full purity range, from 99.03% to 99.99%, with a median of 99.78%, so you can review the spread rather than a single summary figure.

Related guides

Browse third-party tested research materials →
Research use only. For laboratory research use only — not for human or animal consumption. Not a drug, supplement, food, cosmetic, or medical device. Not FDA-approved for any use.
← Back to NovaForge Labs